英语翻译首先说明一下,我要翻译的话是一台设备,我想把一些中文翻译成英文,给用户看的.是一台类似与打印机的喷墨设备!1,请用针筒向喷头里注入20-25毫升的墨水,不能过多或过少.2,每天都要

Question

英语翻译
首先说明一下,我要翻译的话是一台设备,我想把一些中文翻译成英文,给用户看的.是一台类似与打印机的喷墨设备!
1,请用针筒向喷头里注入20-25毫升的墨水,不能过多或过少.
2,每天都要打画,保护你的喷头.长期不用的情况下,请用塑封膜贴好喷头下面的出墨口!
3,如果喷画的时候有一个颜色不出墨了,请用纸巾沾一下喷头下面的出墨口.如果能沾到纸上墨,说明喷头坏了,需要更换了,如果沾不出墨,说明喷头里面的气压不对,请重新调试喷头里的气压(即:喷头里墨水超过25毫升或低20毫升).
4,注意:请接好地线,机器静电特别大.
1、打开加热板，打开电源开关。
2、调整机器左侧的温度控制器，调到180-200摄氏度，
3、机器右侧调整时间，根据材料不同，设置的时间也不一样。
4、当机器达到所设定温度的时候，机器进入恒温状态。
5、加热状态后，将材料拿出来。入冷水使其冷却。
6、大批量工作时，工作60分钟让机器间歇休息2分钟左右！
1、放入杯子，压上手柄，打开电源。
2、调整温度按钮，大概180--200摄氏度。
3、调整时间，大概控制在15秒-20秒。
4、当温度达到温度时进入恒温状态。
5、杯子加热完毕后，将其放入冷水，防止墨扩散。

Answer 1

1,please use the needle tube to spray to infuse into 20-25 milliliters inks in head,can't be excessive or lead little.
2,want to beat a painting everyday,protect you to spray a head.Long-term need not of under circumstance,please seal a that the film sticks to like to spray one underneath of the head a 墨 with the 塑 !
3,if spray time of painting to have a color not 墨 ,please be stained with with the paper towel spray one 墨 all of a sudden.If can be stained with to arrive the paper to ascend 墨 ,the elucidation sprayed a to is out of order ,needing to be replace,if could not be stained with 墨 ,the elucidation sprays one air pressure in the head wrong,please re- adjust to try to spray the air pressure in the head.(namely:spray ink in the head over 25 milliliters of or low 20)
4,attention:please connect goodly line,the machine static electricity is specially big.
The problem add:1,open to heat plank,turn power on a switch.
2,adjust the temperature controller of the machine left side,adjust to 180-200 Celsius degrees,heat for 15-20 minutes.
3,the right side of the machine adjust time,basis material dissimilarity,constitution of time is also different.
4,crash the machine attain the time of set the temperature,the machine enters constant temperature appearance.
5,heat appearance after,take out material.Go into the cold water makes it cool off.
6,the large quantity quantity work,work to make the machine intermittent to take a rest for 60 minutes for about 2 minutes!
1,put into the cup,press to start a handle,turn power on.
2,adjust the temperature button,probably 180-200 Celsius degrees.
3,adjust time,probably control at 15 second-20.
4,be temperature to attain temperature enter constant temperature appearance.
5,the cup heating puts it into a cold water after complete,prevent°froming a 墨 proliferation.