早教吧作业答案频道 -->英语-->
英文翻译,求翻译通畅Thedrivetothecrossprofilemeasurementappearsfromtheparkingposition.Thenormalmeasuringspeediscalculatedfromtheconstanttraversingtimeof2minutesandthepresettraversingwidth.Thetraversingtimeis
题目详情
英文翻译,求翻译通畅
The drive to the cross profile measurement appears from the parking position. The normal measuring speed is calculated from the constant traversing time of 2 minutes and the preset traversing width. The traversing time is adjusted with the measuring electronics. Via control signals between measuring electronics and PLC, a measuring clock for the thickness-and stress measuring is generated. Each thickness value of the cross profile corresponds to the average of the thickness in such a measuring clock.
If the ultrasonic sensor recognizes an object in front of the gauge head, the thickness gauge head is driven to the object, the traversing speed is decreased and the gauge head is driven slowly as long as the gauge head can measure glass or can determine no glass over a length of 10 cm (disturbance object under the gauge head).
The drive to the cross profile measurement appears from the parking position. The normal measuring speed is calculated from the constant traversing time of 2 minutes and the preset traversing width. The traversing time is adjusted with the measuring electronics. Via control signals between measuring electronics and PLC, a measuring clock for the thickness-and stress measuring is generated. Each thickness value of the cross profile corresponds to the average of the thickness in such a measuring clock.
If the ultrasonic sensor recognizes an object in front of the gauge head, the thickness gauge head is driven to the object, the traversing speed is decreased and the gauge head is driven slowly as long as the gauge head can measure glass or can determine no glass over a length of 10 cm (disturbance object under the gauge head).
▼优质解答
答案和解析
在去截面测量似乎从停车位置.正常的测量计算速度持续不断的穿越时间的2分钟和预设穿越宽度.穿越时间调整与测量电子.通过控制之间的信号测量电子和PLC,测量时钟的厚度和应力测量是生成的.每一厚度值对应的截面的平均厚度在这样一个测量时钟.如果超声传感器识别一个对象在前面的表头,厚度测头是驱动对象,穿过速度减少和测头是驱动慢慢只要测头测量玻璃或可以确定没有玻璃长10厘米
看了英文翻译,求翻译通畅Thedr...的网友还看了以下：
若a,b属于R+,a≠b,p=a^(k+1)+b^(k+1),Q=a(b^k)+(a^k)b,(k∈ 2020-03-31 …
下列程序段的输出结果是B.int*p,*q,k=1,j=10;p=&j;q=&k;p=q;(*p) 2020-05-14 …
周长除以面积的二分之一次方,是个什么系数?有什么意义?周长为P,面积为A,则K=P/A^0.5 2020-05-14 …
境界线上的地平线中的P.A.Oda,K.P.A.Italy,三征西班牙,六护式法兰西的意义 2020-05-16 …
随机变量X服从二项分布,其概率分布P{X=k}=C(n,k)p^kq^n-k,(k=1,2,... 2020-05-23 …
设随机变量X的分布律为P（X=k）=a(λ^k)/k!,(k=0,1,2,…）,其中λ>0.当k为 2020-08-03 …
若规定一种对应关系f(k),使其满足：f(k)=(p,q)且q-p=k,若f(k)=(p,q),则f 2020-12-01 …
排列证明：P(m,n)=P（k,n）P（m-k,n-k）P（m,n）=n!/(n-m)!P(k,n) 2020-12-05 …
根据图画和句意填单词。1.-What’sthisin?-It’sa.-Howcanyouit?-B- 2020-12-09 …
已知P{X=k}=a/k,P{Y=-k}=b/k^2(k=1,2,3)X与Y独立,试确定a,b的值并 2021-01-13 …