英语翻译ZLK型无接触主令控制开关ZLKtypewithout（导叶位置开关）一、概述ZLX型无接触主令控制开关作为水轮发电机组自动化元件用来反映水轮机导叶开度并在各个不同开度位置输出相应的

Question

英语翻译
ZLK 型无接触主令控制开关
ZLK type without
（导叶位置开关）
一、 概述
ZLX 型无接触主令控制开关作为水轮发电机组自动化元件用来反映水轮机导叶开度并在各个不同开度位置输出相应的接点信号.
该装置由磁记忆开关组及磁触头组成,两个磁触头装在接力器指针杆上,磁记忆开关组安装在接力器支架上（见附图）.导叶开度变化时,接力器活塞杆带着磁头一起移动.磁头端部与记忆开关组的不锈钢外壳保持2至6毫米距离之间平行移动.当磁头移动接近某个记忆开关时,该开关发出接点信号,并将接点动作记忆下来.每个开关均为一常开、一常闭互为切换.该型主令开关为无接触式新型产品,检测之间仅靠磁力联系,没有任何机械接触,不存在卡阻问题,工作十分可靠.
二、 技术数据
1、 型号规格（见附表）
接力器量程
接点个数
主令开关型号
2、接点容量：
DC100W：最大220V或最大0.5A
AC200VA：最大220V或最大1A
三、 安装及调整
1、 将记忆开关组外壳牢固安装定位在接力器支架上.
2、 按附图正确安装磁触头.
3、 单独调整每个记忆开关的位置,可以方便整定发信号位置.倘若行程极端位置不够调整时,可以卸去引线夹板,将记忆开关再往外调整一段距离.
四、 结构及安装图
1、 安装孔
2、 磁记忆开关
3、 接力器支架
4、 接力器指针杆
5、 接力器活塞杆
6、 磁触头
7、 型号
翻译成英文

Answer 1

ZLK type non-contact master control switch
I.OVERVIEW
ZLX-type non-contact switch as a master control automation group Hydrogenerator turbine components to reflect I.Kai-Qi Ye degrees and in different locations opening of the output signal corresponding contact.
Magnetic memory from the device and the magnetic switch contact group composed of two magnetic contact with the guide pole relay,magnetic memory installed in the switch group relay rack (see figure).I.Kai-Qi Ye of changes in the relay with a head-rod movement together.Head end of the switch and memory group stainless steel casing to maintain 2-6 mm distance between the parallel movement.When the head near a mobile memory switch,the switch contact sent signals,and contact memory moves down.Each switch are a regular set,a normally closed switch each other.This type of master switch for the non-contact type of new products,simple structure,testing links between magnetic alone,without any mechanical contact,and there is no resistance card,work is very reliable.
Second,technical data
1,Model specifications (see table)
Relay Range
Contact number
Master Switch Model
2,contact capacity:
DC100W:Maximum of 220 V or A maximum of 0.5
AC200VA:Maximum of 220 V or A maximum 1
Third,installation and adjustment
1,the group will switch memory location in the shell firmly installed relay bracket.
2,on the attached map correctly install magnetic contact.
3,Individual adjustment of the location of each memory switch,it will be convenient for the whole of the signal location.If not adjusted itinerary extreme position,stepped down can lead splint will be adjusted out of memory to switch some distance.
4,structure and installation plans
1,mounting holes
2,Magnetic Memory Switch
3,relay rack
4,Relay-pointer
5,relay rod
6,magnetic contacts
7,Model